18watt Audio Amplifier

High Quality very simple unit, No need for a preamplifier

Circuit Diagram:

18watt Audio Amplifier

Circuit Diagram:

Power Supply circuit Diagram

Amplifier parts:

P1 = 22K
R1 = 1K
R2 = 4K7
R3 = 100R
R4 = 4K7
R5 = 82K
R6 = 10R-1/2W
R7 = 22R
R8 = 1K-1/2W (optional)
C1 = 470nF-63V
C2 = 100µF-3V Tantalum bead Capacitors
C3 = 470µF-25V
C4 = 470µF-25V
C5 = 100µF-3V Tantalum bead Capacitors
C6 = 100nF-63V
D1 = 1N4148
IC1 = TLE2141C
Q1 = BC182
Q2 = BC212 50V 100mA PNP Transistor
Q3 = TIP42A
Q4 = TIP41A
J1 = RCA audio input socket

Power supply parts:

R9 = 2K2
C7 = 4700µF 25V
C8 = 4700µF 25V
D2 = 100V 4A Diode bridge
D3 = 5mm. Red LED
T1 = 30VCT, 50VA Mains transformer
PL1 = Male Mains plug
SW1 = SPST Mains switch

Notes:

Can be directly connected to CD players, tuners and tape recorders.
Do not exceed 23 + 23V supply.
Q3 and Q4 must be mounted on heatsink.
D1 must be in thermal contact with Q1.
Quiescent current (best measured with an Avo-meter in series with Q3 Emitter) is not critical.
Adjust R3 to read a current between 20 to 30 mA with no input signal.
To facilitate quiescent current setting add R8 (optional).
A correct grounding is very important to eliminate hum and ground loops. Connect to the same point the ground sides of J1, P1, C2, C3 & C4. Connect C6 to the output ground.
Then connect separately the input and output grounds to the power supply ground.

Source : www.redcircuits.com

Comments

TDA2030 complete tone control

At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.

PID instruction in Allen Bradley PLC Closed Loop Control

PID instruction in Allen Bradley PLC [Proportional/Integral/Derivative] Closed Loop Control For Processor SLC 5/02SLC 5/03SLC 5/04SLC 5/05 MicroLogix 1200 and MicroLogix 1500 (A special PID file replaces the old integer file control block.) Description of PID in PLC This output instruction is used to control physical properties such as temperature, pressure, liquid level, or flow rate of process loops. The PID instruction normally controls a closed loop using inputs from an analog input module and providing an output to an analog output module as a response to effectively hold a process variable at a desired set point. The PID equation controls the process by sending an output signal to the actuator. The greater the error between the setpoint and the process variable input, the greater the output signal, and vice versa. An additional value (feed forward or bias) can be added to the control output as an offset. The result of the PID calculation (control vari...

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity. FMAX = 1 MHz WIDE 1000:1 Continuous Sweep Possible NE566 Function Generator Circuit Diagram Pdf Datasheet Sourced by : Circuitsstream

Mutchus

Search This Blog