87 108MHz FM Wireless Microphone

This FM wireless microphone is easy to build and has a useful range of transmission (over 300 meters outdoors). Despite its small number of components and an operating voltage of 3V to easily penetrate over three floors of an apartment building. You can tune anywhere on the FM band (87-108MHz) and its transmissions can be picked up at any point of view of the FM receiver.

The coil (L1) should be approximately 3 mm in diameter, 5 turns 0.61 mm copper wire. You can vary the Tx frequency by simply adjusting the distance between the coils. The antenna should be a half wavelength or quarter-time (100 MHz, 150 cm or 75 cm).

Parts list:

T1,T2,T3: 2N2222 transistor
R1: 10k 5%
R2: 33k lin.
R3: 12k 5%
R4: 5.6k 5%
R5: 2.2k 5%
R6,R8: 47k 5%
R7: 470 ohms 5%
R9: 180 ohms 5%
C1,C2: 47nF
C3: 1nF
C4: 33pF
C5: 5.6pF
C6: 8.2pF
C7: 10nf
L1: 3mm in diameter with 5 turns 0.61 mm copper wire
K1: SPDT toggle switch
Other parts: 2 AA battery holder, Electret microphone, antenna wire

Comments

TDA2030 complete tone control

At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.

PID instruction in Allen Bradley PLC Closed Loop Control

PID instruction in Allen Bradley PLC [Proportional/Integral/Derivative] Closed Loop Control For Processor SLC 5/02SLC 5/03SLC 5/04SLC 5/05 MicroLogix 1200 and MicroLogix 1500 (A special PID file replaces the old integer file control block.) Description of PID in PLC This output instruction is used to control physical properties such as temperature, pressure, liquid level, or flow rate of process loops. The PID instruction normally controls a closed loop using inputs from an analog input module and providing an output to an analog output module as a response to effectively hold a process variable at a desired set point. The PID equation controls the process by sending an output signal to the actuator. The greater the error between the setpoint and the process variable input, the greater the output signal, and vice versa. An additional value (feed forward or bias) can be added to the control output as an offset. The result of the PID calculation (control vari...

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity. FMAX = 1 MHz WIDE 1000:1 Continuous Sweep Possible NE566 Function Generator Circuit Diagram Pdf Datasheet Sourced by : Circuitsstream

Mutchus

Search This Blog