Skip to main content

Atomic Structure Definition Key Points


3.4 Atomic Structure Definition Key Points

1.       Matter is anything that occupies space and has mass.
2.       The smallest particle of matter that can take part in a chemical reaction is called an atom.
3.       An atom consists of protons, neutrons and electrons.
4.       The protons and neutrons form the nucleus of the atom.
5.       Protons and neutrons are collectively known as nucleons.
6.       The atomic number of an element indicates the number of protons in the nucleus of its atom.
7.       The number of electrons in the outermost orbit is the valence electrons.
8.       Electrons carry a negative charge; while protons carry a positive charge. Charged atoms or molecule are called ions.
9.       Most metals contain free electrons which, at room temperatures, roam the spaces between the atoms.
10.    In most substances, atoms team up to form molecules.
11.    Electrons moving in a given direction give rise to an electric current. An electric circuit is a closed path through which an electric current may flow.
12.    Electrically, materials can be grouped as:
a.        conductors,
b.       semi-conductors, and
c.        insulators.
13.    Conductors are those materials which have free electrons. The most common conductors are made of copper and aluminium.
14.    Semi-conductors have few free electrons at low temperatures, but have many free electrons at higher temperatures.
15.    The most commonly used semi-conductors are silicon and germanium. They are used for making diodes, transistors and integrated circuits.
16.    Insulators have no free electrons and do not conduct an electric current.

Comments

Popular posts from this blog

PID instruction in Allen Bradley PLC Closed Loop Control

PID instruction in Allen Bradley PLC [Proportional/Integral/Derivative] Closed Loop Control For   Processor SLC 5/02SLC 5/03SLC 5/04SLC 5/05    MicroLogix 1200 and MicroLogix 1500 (A special PID file replaces the old integer file control block.) Description of PID in PLC   This output instruction is used to control physical properties such as temperature, pressure, liquid level, or flow rate of process loops. The PID instruction normally controls a closed loop using inputs from an analog input module and providing an output to an analog output module as a response to effectively hold a process variable at a desired set point. The PID equation controls the process by sending an output signal to the actuator. The greater the error between the setpoint and the process variable input, the greater the output signal, and vice versa. An additional value (feed forward or bias) can be added to the control output as an offset. The result of the PID calculation (control vari...

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity.  FMAX = 1 MHz     WIDE 1000:1 Continuous Sweep Possible  NE566 Function Generator Circuit Diagram Pdf Datasheet  Sourced by : Circuitsstream

Long Loopstick Antenna Circuit Diagram

Circuit Diagram  Description Wound on a 3 foot length of PVC pipe, the long loopstick antenna was an experiment to try to improve AM radio reception without using a long wire or ground. It works fairly well and greatly improved reception of a weak station 130 miles away. A longer rod antenna will probably work better if space allows. The number of turns of wire needed for the loopstick can be worked out from the single layer, air core inductance formula: Inductance = (radius^2 * turns^2) / ((9*radius)+(10*length)) where dimensions are in inches and inductance is in microhenrys. The inductance should be about 230 microhenrys to operate with a standard AM radio tuning capacitor (33-330 pF). The 3 foot PVC pipe is wound with approximately 500 evenly spaced turns of #24 copper wire which forms an inductor of about 170 microhenrys, but I ended up with a little more (213uH) because the winding spacing wasn't exactly even. A secondary coil of about 50 turns is wound along the length of th...