Skip to main content

Glow Plug Controller


In diesel engines, the air in the cylinders is not hot enough to ignite the fuel under cold conditions. Therefore each cylinder of these engines is fitted with an electric heater known as ‘glow plug.’ A control circuit is necessary to optimise the functioning of glow plugs. It raises the air temperature inside the engine cylinder for quick and reliable starting, extended battery life and reduced diesel consumption.
The glow plug controller (Fig. 1) uses a simple timer circuit built around MOSFET T1 for reliability and simplicity. Momentary pushing of switch S2 charges capacitor C1 rapidly via resistor R1. When the voltage on capacitor C1 exceeds the threshold voltage of the gate (G) of MOSFET T1, it starts charging reservoir capacitor C2 and simultaneously energises relay RL1. MOSFET T1 remains conducting as long as the voltage on C1 is greater than the threshold voltage of the MOSFET gate.
The ‘on’ time period depends on the value of capacitor C1 and resistor R2, which govern the discharge current of capacitor C2. The component values given here will produce ‘on’ time of around 25 seconds. In effect, when you
press switch S2 momentarily, the relay energises for about 25 seconds and the glow plug gets the power supply through its contact.
The red LED (LED1) indicates that the heating process of glow plugs is ‘on.’ When the ‘on’ time is over, the green LED (LED2) turns on for a while, followed by a short beep from the buzzer, which indicates that the engine is ready for starting. Glow plugs draw a heavy current, hence high-current rating contacts of an automotive relay are required.
Assemble the circuit on any general purpose PCB and house in a suitable case. Connect the glow plug wire to the relay contact. 12V battery already available with the vehicle is used to power the circuit. Connect the piezo buzzer and LED1 and LED2 through an external connection and place it at a convenient location for the driver to operate.


Schematic:
Fig. 2. Glow Plug Controller
Pin Configuration:
Component Required:
R1,       220 ohm
R2,       1.5M ohm
R3,       15K ohm
R4,       1K ohm
D1,       1N4001
T1,       BS170
T2,       BC548
C1,       10uF/ 25V electrolyte
C2,       1000uF/ 25V electrolyte
PZ1,     Piezo Buzzer
S1,       on/off Switch
S2,       push to on Switch
LED1,    red LED
LED2,   green LED
RL1,     12v High current

Comments

Popular posts from this blog

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity.  FMAX = 1 MHz     WIDE 1000:1 Continuous Sweep Possible  NE566 Function Generator Circuit Diagram Pdf Datasheet  Sourced by : Circuitsstream

TDA2030 complete tone control

At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.

Simple Preamplifier and High to Low impedance Converter Circuit Diagram

This is the Simple Preamplifier and High to Low impedance Converter Circuit Diagram. This circuit matches the very high impedance of ceramic cartridges, unity gain, and low impedance output.  Simple Preamplifier and High to Low impedance Converter Circuit Diagram By `loading` the cartridge with a 2M2 input resistance, the cartridge characteristics are such as to quite closely compensate for the RIAA recording curve. The output from this preamp may be fed to a level pot for mixing. Sourced By: Circuitsproject