How to build 1 5V to 5V 12V DC DC Converter with LT1073

Small 1.5V to 5V or 12V DC/DC converter with LT1073 chip. The IC is available in three different versions, depending on output voltage. Two with fixed output voltage of 5V and 12V, and the most interesting that can be adjusted. The adjustment is done through a voltage divider with two resistors, of mass, output and Terminal 8, internally connected to the voltage comparator IC, which is responsible for stabilizing the output voltage.

LT1073 has an internal everything you need to make a small DC / DC converter with a low operating voltage of only 95μA 1V and consumption without load.

If you do not have a meter inductance, the inductive part of the drive is a bit more complicated to make, but we shall see some possible solutions. Capacitor also recommended by the manufacturer for the circuit is a bit hard to get, I have used a tantalum recovered from another power source, and the ripple voltage at the output is quite low. Last but not least, say that the diode has to be a fast, not worth as the 1N4002 rectifiers, the 1N5818 is recommended schottky type, characterized by high response time and low internal resistance, which is what ideal for this type of converters.

As we can see from the photograph of the circuit in a low energy lamp, ay a small toroidal core can be recovered. 82μH To this core, we winding 7 turns of 0.3mm enamelled copper wire.

Another option is to use a toroidal core Ferroxcube, Farnell code 178-504 of 13.25 x7, 35x5, 7mm, grade 3C85, value AL 1000. with this core we have winding 8 turns to 90μH.

Finally, note that you can download the documentation in the manufacturer's website, is very good and complete, with numerous examples of applications, and above all very clear.

1.5V to 5V/12V DC/DC Converter with LT1073 ab

Comments

PID instruction in Allen Bradley PLC Closed Loop Control

PID instruction in Allen Bradley PLC [Proportional/Integral/Derivative] Closed Loop Control For Processor SLC 5/02SLC 5/03SLC 5/04SLC 5/05 MicroLogix 1200 and MicroLogix 1500 (A special PID file replaces the old integer file control block.) Description of PID in PLC This output instruction is used to control physical properties such as temperature, pressure, liquid level, or flow rate of process loops. The PID instruction normally controls a closed loop using inputs from an analog input module and providing an output to an analog output module as a response to effectively hold a process variable at a desired set point. The PID equation controls the process by sending an output signal to the actuator. The greater the error between the setpoint and the process variable input, the greater the output signal, and vice versa. An additional value (feed forward or bias) can be added to the control output as an offset. The result of the PID calculation (control vari...

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity. FMAX = 1 MHz WIDE 1000:1 Continuous Sweep Possible NE566 Function Generator Circuit Diagram Pdf Datasheet Sourced by : Circuitsstream

Long Loopstick Antenna Circuit Diagram

Circuit Diagram Description Wound on a 3 foot length of PVC pipe, the long loopstick antenna was an experiment to try to improve AM radio reception without using a long wire or ground. It works fairly well and greatly improved reception of a weak station 130 miles away. A longer rod antenna will probably work better if space allows. The number of turns of wire needed for the loopstick can be worked out from the single layer, air core inductance formula: Inductance = (radius^2 * turns^2) / ((9*radius)+(10*length)) where dimensions are in inches and inductance is in microhenrys. The inductance should be about 230 microhenrys to operate with a standard AM radio tuning capacitor (33-330 pF). The 3 foot PVC pipe is wound with approximately 500 evenly spaced turns of #24 copper wire which forms an inductor of about 170 microhenrys, but I ended up with a little more (213uH) because the winding spacing wasn't exactly even. A secondary coil of about 50 turns is wound along the length of th...

Mutchus

Search This Blog