Skip to main content

LED at 230 V Circuit Project


Small circuit to run a LED on line voltage (English) This little circuit allows to connect a LED to line voltage. A LED can not handle with 230V AC and needs a current which is limted to ca. 15mA. The first issue is simply solved with a diode which eliminates the voltage in reverse-biasing. The current is limited by the combination of the resistor and capacitor. Used at AC capacitors work as frequency dependent resistors. You can simply calculate the capacitive resistance of the capacitor by the following formula:


Formula to calculate the capacitive resistance


Based on a frequency of 50Hz and a capacity of 220nF you get a reactance of ca. 16kΩ. This is just perfect for a LED. The resistor prevents that the capacitor does not charge that abruptly.

Hinweis

Attention. This circuit works with life threatening line voltage. All parts of this circuit are connected to the grid! You have to make sure that it is not possible to touch any parts of the circuit at any time. You have to unplug the circuit everytime you want to check it.

Part list

  • C1: foil capacitor 220nF, 250V~ (stick to the values!)
  • R1: 2,2kΩ
  • R2: 220Ω
  • D1: 1N4007 (or comparable; must be suitable for 220V/230V)
  • LED1: standard LED

Circuit diagram

Circuit diagram



 

 

Source by : Benedikt Wirmer


Labels:

Comments

Post a Comment

Popular posts from this blog

PID instruction in Allen Bradley PLC Closed Loop Control

PID instruction in Allen Bradley PLC [Proportional/Integral/Derivative] Closed Loop Control For   Processor SLC 5/02SLC 5/03SLC 5/04SLC 5/05    MicroLogix 1200 and MicroLogix 1500 (A special PID file replaces the old integer file control block.) Description of PID in PLC   This output instruction is used to control physical properties such as temperature, pressure, liquid level, or flow rate of process loops. The PID instruction normally controls a closed loop using inputs from an analog input module and providing an output to an analog output module as a response to effectively hold a process variable at a desired set point. The PID equation controls the process by sending an output signal to the actuator. The greater the error between the setpoint and the process variable input, the greater the output signal, and vice versa. An additional value (feed forward or bias) can be added to the control output as an offset. The result of the PID calculation (control vari...
Post a Comment
Read more

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity.  FMAX = 1 MHz     WIDE 1000:1 Continuous Sweep Possible  NE566 Function Generator Circuit Diagram Pdf Datasheet  Sourced by : Circuitsstream
Post a Comment
Read more

Long Loopstick Antenna Circuit Diagram

Circuit Diagram  Description Wound on a 3 foot length of PVC pipe, the long loopstick antenna was an experiment to try to improve AM radio reception without using a long wire or ground. It works fairly well and greatly improved reception of a weak station 130 miles away. A longer rod antenna will probably work better if space allows. The number of turns of wire needed for the loopstick can be worked out from the single layer, air core inductance formula: Inductance = (radius^2 * turns^2) / ((9*radius)+(10*length)) where dimensions are in inches and inductance is in microhenrys. The inductance should be about 230 microhenrys to operate with a standard AM radio tuning capacitor (33-330 pF). The 3 foot PVC pipe is wound with approximately 500 evenly spaced turns of #24 copper wire which forms an inductor of about 170 microhenrys, but I ended up with a little more (213uH) because the winding spacing wasn't exactly even. A secondary coil of about 50 turns is wound along the length of th...
Post a Comment
Read more