LG RZ32LZ55 32 inch LCD TV Schematic

Video control and display data: Video signal is received from TUNER, AV port(AV1,AV2,S-Video,Component) and goes to the one-chip video decoder (VCTI) which separate the R,G,B signal and passes on the signal to AD converter(AD9883) which converts 4:4:4 video format into digital and gives output to the Picture Enhancer(FLI2300).This picture enhancer improves the quality of the picture by changing the level of RGB signals. The output of this enhancer chip is fed to the deinterlacer ,which in turn goes to the Scalar (GM5221).The scalar gives the output on the LVDS cable which is connected to LCD module. VCTi acts a micom and is responsible for video processing and audio signal processing. It accepts the RF signal and separates sound and picture from it. Scaler is responsible for regulating the timing of signal to LCD panel and size and location of the signal. Graphic control accepts the PC(Analog RGB) and DVI-D (Digital ) signal, Scalar is responsible for regulating the timing of signal to LCD panel and size and location of the signal. Graphic control accepts the PC(Analog RGB) and DVI-D (Digital ) signal,the signal of PC input is connected to analog port in Scaler and the signal of DVI-D input is connected to digital port. Thus it receives two input and switch between them to give output at the LVDS which in turn gives output at the LCD module.

Schematic

Power unit:The power board supplies a DC voltage of 33V, 24V, 12V to the main board.out of this 33v is used by the tuner and 24v is used directly by the inverter and the sound amplifier IC. 24v also is converted into 5v by a regulator. The 5v is changed into 3.3v and 1.8v by a regulator, both voltages(3.3v, 1.8v ) is used by VCTI, Scaler, FLI2300 and AD9883. The voltage of LCD Panel is 12v.

Comments

PID instruction in Allen Bradley PLC Closed Loop Control

PID instruction in Allen Bradley PLC [Proportional/Integral/Derivative] Closed Loop Control For Processor SLC 5/02SLC 5/03SLC 5/04SLC 5/05 MicroLogix 1200 and MicroLogix 1500 (A special PID file replaces the old integer file control block.) Description of PID in PLC This output instruction is used to control physical properties such as temperature, pressure, liquid level, or flow rate of process loops. The PID instruction normally controls a closed loop using inputs from an analog input module and providing an output to an analog output module as a response to effectively hold a process variable at a desired set point. The PID equation controls the process by sending an output signal to the actuator. The greater the error between the setpoint and the process variable input, the greater the output signal, and vice versa. An additional value (feed forward or bias) can be added to the control output as an offset. The result of the PID calculation (control vari...

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity. FMAX = 1 MHz WIDE 1000:1 Continuous Sweep Possible NE566 Function Generator Circuit Diagram Pdf Datasheet Sourced by : Circuitsstream

Long Loopstick Antenna Circuit Diagram

Circuit Diagram Description Wound on a 3 foot length of PVC pipe, the long loopstick antenna was an experiment to try to improve AM radio reception without using a long wire or ground. It works fairly well and greatly improved reception of a weak station 130 miles away. A longer rod antenna will probably work better if space allows. The number of turns of wire needed for the loopstick can be worked out from the single layer, air core inductance formula: Inductance = (radius^2 * turns^2) / ((9*radius)+(10*length)) where dimensions are in inches and inductance is in microhenrys. The inductance should be about 230 microhenrys to operate with a standard AM radio tuning capacitor (33-330 pF). The 3 foot PVC pipe is wound with approximately 500 evenly spaced turns of #24 copper wire which forms an inductor of about 170 microhenrys, but I ended up with a little more (213uH) because the winding spacing wasn't exactly even. A secondary coil of about 50 turns is wound along the length of th...

Mutchus

Search This Blog