Skip to main content

Power Amplifier Using STK3048A for driver input


STK6153 production and use STK3048A amplifier, you reported to have introduced a lot, of which there are many improving circuit, but limited to the STK6153 performance, making the sets of combination play to the top circuit performance is not necessarily the broad masses of Shao You can meet the requirements. In this paper, STK3048A for voltage amplification, Coupled with ultra-dynamic bias circuit at the end of the production of a super-A amplifier.

Power Amplifier Using STK3048A Circuit Schematic 

Power-Amplifier-use-STK3048A-for-driver-input-Circuit Diagram

Below the production elements and brief debugging. Transistor matching error should be 5 percent, the midpoint of migration can be controlled in less than 10 mV. Heat sink should try to get some large, to ensure the safety of power, the general weight of not less than 1,2 kg (two channels), if conditions allow the best and a small 12 V equipment Low Noise fans, for a mandatory cooling. Map k Ω resistance are blocked 0,5 W, Ω block resistance are 1 W, 0,22 Ω resistor is optional 5 W white ceramic resistance. Amp welding after the completion of inspection to correct power debug, W1 decided to amp static bias, the first upward resistance will be transferred to the most, then the smallest amp static bias, access to power, touch all of the phenomenon should be no fever . Potential inspection centres in 10 mV around, gradually changing the resistance W1 (down), so that only 0,22 Ω resistance on both ends voltage of 0,05 V can be, then each of the quiescent current for about 220 mA, and then resume Centre for Migration should be measured in less than 20 mV. W2 resistance decided to "super A" component current size.

For each preference may be, may generally be rotating to the center position value. 10 minutes after the re-testing of the data points can be put into trial if the same sound. As for the effect, to try Pianzhi. Local output power of 70 W +70 W.


Comments

Popular posts from this blog

Transceiver Homebrew QRP SSB 80M Band

Radio communication transceiver is a radio transmitter at the same time the plane doubles as a radio receiver used for communication purposes. It consists of the transmitter and the receiver are assembled in an integrated way. In mulamula generation, the transmitter or receiver or transmitter and receiver sections are assembled separately and is part of a stand sendirisendiri and can work well sendirisendiri Currently employed both parts are integrated in turn. Aircraft simple transmitter consists of an oscillator generating radio vibration and this vibration after vibration boarded with our voice, in a technique called dimodulir radio, then by the antenna is converted into radio waves and transmitted. As we know that the sound waves we can not reach long distances, although its power is quite large, while the radio waves with a relatively small force can reach a distance of thousands of kilometers. In order for our voice can reach a far distance, then our voice superimposed on radio w...

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity.  FMAX = 1 MHz     WIDE 1000:1 Continuous Sweep Possible  NE566 Function Generator Circuit Diagram Pdf Datasheet  Sourced by : Circuitsstream

TDA2030 complete tone control

At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.