Skip to main content

AC Mains Bistable Switch


This AC mains-operated bistable  switch turns on or turns off a  device using a miniature neon  lamp and a few discrete components.  This switch can be used for control pan-els, appliances and lighting controls.  A push-to-on switch is used to  light up the neon lamp. The light emit-ted by the neon lamp, in turn, enables  the switching action of the circuit. Use  of a 555 timer wired for bistable operation makes the circuit act as a bistable  switch.

Circuit diagram :

AC Mains Bistable Switch-Circuit Diagram

AC Mains Bistable Switch Circuit Diagram

The neon lamp (NL1) and the  push-to-on switch (S1) are directly connected to 230V AC mains. The 12V DC  supply for timer 555 (IC1) is derived  from 230V AC mains through capacitive dropper C1, resistor R1 and a 12V  zener diode. IC1 works as a flip-flop  circuit, with the signal at its output  pin 3 toggling every time it receives a  pulse at its pins 2 and 6.

The operation of the circuit is simple. When you press switch S1 momentarily, the neon lamp glows, making  phototransistor T1 conduct to provide  a pulse at pins 2 and 6 of IC1.  When switch S1 is pressed, the output of IC1  goes high and LED1 glows. Pressing S1  again makes the output of IC1 low and  LED1 stops glowing.

In place of LED1, you can use an  optodiac or suitable relay (not shown  in the circuit) along with a suitable  driver circuit to drive AC loads. Assemble the circuit on a general-purpose PCB with the neon lamp and  the phototransistor housed in a small  black tube isolated from the external  light source, and enclose in a suitable  cabinet. Fix switch S1 on the  front panel of the cabinet,  and mains power cord at  the rear. At the rear, also fix  a 3-pin socket to connect the  AC load.

Caution.  Take care  when operating this circuit  as it is directly connected to  230V AC mains. Better still,  don’t attempt this circuit  if you have no experience  in handling high-voltage  circuits.

Author : T.A. Babu- Copyright : EFY


Comments

Popular posts from this blog

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity.  FMAX = 1 MHz     WIDE 1000:1 Continuous Sweep Possible  NE566 Function Generator Circuit Diagram Pdf Datasheet  Sourced by : Circuitsstream

Transceiver Homebrew QRP SSB 80M Band

Radio communication transceiver is a radio transmitter at the same time the plane doubles as a radio receiver used for communication purposes. It consists of the transmitter and the receiver are assembled in an integrated way. In mulamula generation, the transmitter or receiver or transmitter and receiver sections are assembled separately and is part of a stand sendirisendiri and can work well sendirisendiri Currently employed both parts are integrated in turn. Aircraft simple transmitter consists of an oscillator generating radio vibration and this vibration after vibration boarded with our voice, in a technique called dimodulir radio, then by the antenna is converted into radio waves and transmitted. As we know that the sound waves we can not reach long distances, although its power is quite large, while the radio waves with a relatively small force can reach a distance of thousands of kilometers. In order for our voice can reach a far distance, then our voice superimposed on radio w...

Altec Lansing 353A – power amplifier – vacuum tube type – Circuit diagram 6L6 12AX7

Used tubes – 12AX7 [pre-amplifier, tone control and audio pre-amplifier] – 6L6GC [audio output] Circuit diagram Tube pin-out -6L6 Tube pin-out 12AX7