Stereo 30W STK ICs amplifier circuit

This amplifier circuit based on IC STK ic used in which the manifold. And on this circuit ic STK has many similarities, you can use the STK430 ICs, 433, 435, 437, 439, 441, 443, 4332, 4352, 4362, 4372, 4392. Between the specify type IC STK, which has the excellent performance is STK433 and STK443 because it has output, and high amperage, and voltage problems Suplly but I chose IC STK443 because maximum voltage up to 70 volts, compared with the others that just under 60 volts. For a list of components can seen below.

Component List :

Resistor
R1_____1KΩ
R2_____1KΩ
R3_____120Ω
R4_____120Ω
R5_____330KΩ
R6_____22KΩ
R7_____22KΩ
R8_____330KΩ
R9_____12KΩ
R10____220KΩ
R11____220KΩ
R12____12KΩ
R13____100Ω
R14____4Ω7
R15____4Ω7

Capacitor
C1_____4µ7F
C2_____4µ7F
C3_____220µF
C4_____220µF
C5_____100µF
C6_____100µF
C7_____220µF
C8_____100µF
C9_____47µF
C10____47µF
C11____0.1µF
C12____0.1µF
C13____2200µF
C14____2000µF
**Orange on symbol capacitor is plus Elco**

IC
U1_____STK430 , STK433 , STK435 , STK437 , STK439 , STK441 , STK443 , STK4332 , STK4352 , STK4362 , STK4372 , STK4392.

Comments

TDA2030 complete tone control

At this time I present a series of amplifiers that use IC TDA2030, but this series is equipped with a tone control. Tone controls include Bass, Treebel, and Volume. Power amplifier and tone control has been put together in a single PCB. As well as its power supply circuit was also used as one with the power amp, and tone control. Making it easier in the installation and will look neat. Schematics Layout PCB PCB design This amplifier is a mono amplifier type, can be modif for guitar amplifiers. If not coupled amplifier (mic preamp) then you must deactivated potensio treble and bass, why? because if not using a mic preamp and still maintain potensio treble and bass sound input (input) from the guitar will not or the maximum discharge is not tight on the speakers. So you must deactivated a way to decide which directly connected capacitor with the tone control circuit, and capacitor were connected directly to potensio volume and input jack.

PID instruction in Allen Bradley PLC Closed Loop Control

PID instruction in Allen Bradley PLC [Proportional/Integral/Derivative] Closed Loop Control For Processor SLC 5/02SLC 5/03SLC 5/04SLC 5/05 MicroLogix 1200 and MicroLogix 1500 (A special PID file replaces the old integer file control block.) Description of PID in PLC This output instruction is used to control physical properties such as temperature, pressure, liquid level, or flow rate of process loops. The PID instruction normally controls a closed loop using inputs from an analog input module and providing an output to an analog output module as a response to effectively hold a process variable at a desired set point. The PID equation controls the process by sending an output signal to the actuator. The greater the error between the setpoint and the process variable input, the greater the output signal, and vice versa. An additional value (feed forward or bias) can be added to the control output as an offset. The result of the PID calculation (control vari...

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity. FMAX = 1 MHz WIDE 1000:1 Continuous Sweep Possible NE566 Function Generator Circuit Diagram Pdf Datasheet Sourced by : Circuitsstream

Mutchus

Search This Blog