Kawasaki KLR250 Oil Filter Cross Reference

We thought that many of you would find this useful. Next time you're looking for an oil filter for your KLR250 motorcycle you won't have to goto the dealer to get one. Here is a cross reference list of oil filters that will fit the Kawasaki KLR 250. Be sure to double check that the filter is the correct one for your bike before use.

KLR250 Oil Filter Cross Reference
Kawasaki - 16099-004
Amsoil - 24941
Big A - 96950
Big A - 96951
Carquest - 89951
Champ - P7027
Emgo - 10-30000 (Buy)
Fram - CH6070 (Buy)
Hastings - LF582
HiFloFiltro - HF123
K&N - KN-123 (Buy)
Lunefiner - P7027
Napa - 4950
Napa - 4951
Parts Unlimited - 16099-004 (Buy)
Purolator - ML16823 (Buy)
Purolator - ML16824
Scotts (stainless) - 2148
Warner - P7027
Wix - 24951 (Buy)

Note: Although the Fram CH6070 should fit in the KLR we have heard from a few owners who have experienced fitment issues with this filter due to it being a little too long. It seems as though Fram has quality control issues with these filters. If you are using this filter we strongly suggest you compare its length next to your current filter before installation.

Comments

PID instruction in Allen Bradley PLC Closed Loop Control

PID instruction in Allen Bradley PLC [Proportional/Integral/Derivative] Closed Loop Control For Processor SLC 5/02SLC 5/03SLC 5/04SLC 5/05 MicroLogix 1200 and MicroLogix 1500 (A special PID file replaces the old integer file control block.) Description of PID in PLC This output instruction is used to control physical properties such as temperature, pressure, liquid level, or flow rate of process loops. The PID instruction normally controls a closed loop using inputs from an analog input module and providing an output to an analog output module as a response to effectively hold a process variable at a desired set point. The PID equation controls the process by sending an output signal to the actuator. The greater the error between the setpoint and the process variable input, the greater the output signal, and vice versa. An additional value (feed forward or bias) can be added to the control output as an offset. The result of the PID calculation (control vari...

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity. FMAX = 1 MHz WIDE 1000:1 Continuous Sweep Possible NE566 Function Generator Circuit Diagram Pdf Datasheet Sourced by : Circuitsstream

Long Loopstick Antenna Circuit Diagram

Circuit Diagram Description Wound on a 3 foot length of PVC pipe, the long loopstick antenna was an experiment to try to improve AM radio reception without using a long wire or ground. It works fairly well and greatly improved reception of a weak station 130 miles away. A longer rod antenna will probably work better if space allows. The number of turns of wire needed for the loopstick can be worked out from the single layer, air core inductance formula: Inductance = (radius^2 * turns^2) / ((9*radius)+(10*length)) where dimensions are in inches and inductance is in microhenrys. The inductance should be about 230 microhenrys to operate with a standard AM radio tuning capacitor (33-330 pF). The 3 foot PVC pipe is wound with approximately 500 evenly spaced turns of #24 copper wire which forms an inductor of about 170 microhenrys, but I ended up with a little more (213uH) because the winding spacing wasn't exactly even. A secondary coil of about 50 turns is wound along the length of th...

Mutchus

Search This Blog