Kawsaki KLR250 Paint and Plastic Color Combinations

Like we mentioned earlier Kawasaki changed very few things on the KLR250 during its lifespan. The most prominent change was the varying paint and plastic color combinations. When trying to do research for the color combinations for each year of the KLR 250 we had a hard time finding much solid information as it varied from source to source. Wikipedia had a pretty comprehensive list but it didnt seem to match up with other sources. With that said here is our list of the color combos for each year. If you have more information on what we have right or wrong please let us know.

-1985 and 1986 Lime Green or White/Blue
lime green klr 250 1985

Thomas Perley Doon's 1985 KLR250 (source)

blue and white klr250 1986

Randy's 1986 KLR250 (source)

-1987 White/Blue/Red
red white and blue patriotic kawi klr250 1987

Tom Bakewell's 1987 KLR250 (source)

-1988 to 1989 White/Blue/Green
white blue and green klr250 klr 250 1988 1989

Triston Rynott's 1989 KLR250 (source)

-1990 to 1993 White/Light Blue
1990 1991 1992 1993 klr 250

Koop's 1991 KLR250 (source)

-1994 to 1996 Teal/Purple -These years were often referred to as the Barbie years because of the odd teal and purple paint scheme which looks like something Ken and Barbie would ride.
barbie purple teal klr250 1994 1995 1996

barbie purple teal klr250 1994 1995 1996

Ben's 1995 KLR250 (source)

-1997 to 1999 Dark Bluish Green
blue green klr250 1997 1998

Keith MacDermott's 1998 KLR250 (source)

-2000 Olive Green/Black
2000 army olive green klr250

Zachary's 2000 KLR250 (source)

-2001 to 2002 Silver/Olive Green
2001 2002 klr250

-2003 Black/Olive Green
2003 black and green klr250

Michael Ebersole's 2003 KLR250 (source)

-2004 to 2005 Black/Red
red and black klr 250

*All images copyright of their respective owners. Most images courtesy of Bikepics.com

Comments

PID instruction in Allen Bradley PLC Closed Loop Control

PID instruction in Allen Bradley PLC [Proportional/Integral/Derivative] Closed Loop Control For Processor SLC 5/02SLC 5/03SLC 5/04SLC 5/05 MicroLogix 1200 and MicroLogix 1500 (A special PID file replaces the old integer file control block.) Description of PID in PLC This output instruction is used to control physical properties such as temperature, pressure, liquid level, or flow rate of process loops. The PID instruction normally controls a closed loop using inputs from an analog input module and providing an output to an analog output module as a response to effectively hold a process variable at a desired set point. The PID equation controls the process by sending an output signal to the actuator. The greater the error between the setpoint and the process variable input, the greater the output signal, and vice versa. An additional value (feed forward or bias) can be added to the control output as an offset. The result of the PID calculation (control vari...

NE566 Function Generator Circuit Diagram

The NE566 Function Generator is a Voltage-Controlled Oscillator of exceptional linearity with buf fered square wave and triangle wave outputs. The frequency of oscillation is determined by an external resistor and capacitor and the voltage applied to the control terminal. The Oscillator CAN be programmed over a ten-to-one frequency range by proper selection of an external resistance and modulated over a ten-to-one range by the control voltage, with exceptional linearity. FMAX = 1 MHz WIDE 1000:1 Continuous Sweep Possible NE566 Function Generator Circuit Diagram Pdf Datasheet Sourced by : Circuitsstream

Long Loopstick Antenna Circuit Diagram

Circuit Diagram Description Wound on a 3 foot length of PVC pipe, the long loopstick antenna was an experiment to try to improve AM radio reception without using a long wire or ground. It works fairly well and greatly improved reception of a weak station 130 miles away. A longer rod antenna will probably work better if space allows. The number of turns of wire needed for the loopstick can be worked out from the single layer, air core inductance formula: Inductance = (radius^2 * turns^2) / ((9*radius)+(10*length)) where dimensions are in inches and inductance is in microhenrys. The inductance should be about 230 microhenrys to operate with a standard AM radio tuning capacitor (33-330 pF). The 3 foot PVC pipe is wound with approximately 500 evenly spaced turns of #24 copper wire which forms an inductor of about 170 microhenrys, but I ended up with a little more (213uH) because the winding spacing wasn't exactly even. A secondary coil of about 50 turns is wound along the length of th...

Mutchus

Search This Blog